Skip to content
Black and white metallic epoxy floor in a high-bay suite, a man in black walking toward a roll-up door under exposed ducts and strip lights
Warehouse

Working Floors for the Ag Buildings Around San Juan Bautista

Outside town, the buildings that need a hard floor are mostly working ones: equipment sheds, storage warehouses, shops that sit right against the fields. Their slabs have taken years of diesel, hydraulic fluid and dust. Johnny Mendoza reads all of that before he decides how much grinding a floor needs. Harvest and wind usually set the pour date more than we do.

Dual certified, JP Resin and Don Resin · Hollister shop, fifteen minutes away

What years of farm work leave in a slab

A slab that has lived under tractors, trucks and forklifts carries its history in the pores. Diesel and hydraulic fluid soak in and keep wicking back toward the surface long after the spill was mopped up. A coating laid over that can look fine for a season and then lift in patches, usually right where the equipment parks.

So prep starts with chemistry. The floor is degreased, then ground hard enough to open the concrete and take off the contaminated layer. Then Johnny checks it. If oil is still surfacing, the floor gets another round of cleaning and grinding before any primer is mixed. That extra pass decides whether the coating holds.

Oil left in the concrete waits. The peel shows up months later, right over the stain everyone thought was gone.

None of this is visible from the doorway. Johnny looks hardest at the dark patches near the roll-up doors and under the spots where machines sit overnight, since those are the places a second pass is most likely. He tells you what he finds before anything is priced.

Old coatings and sealers are part of the same story. A lot of farm buildings carry a painted floor or a cheap sealer from years back, worn off in the lanes and still stuck in the corners. Whatever is loose comes up under the grinder, so the new system bonds to the slab itself and to nothing that was laid before it.

The topcoat gets picked for what spills in that particular building. A shop that handles fuel, oil and cleaners every week needs a finish that holds up to all of it, and Johnny asks what actually ends up on the floor before he settles on one.

Buildings Where warehouse floors go

The buildings outside town

Most warehouse-type floors around San Juan Bautista sit near working farmland, and each kind of building brings its own trouble.

Equipment sheds

Tractors and trucks drip diesel and hydraulic fluid in the same places for years. These floors get the deepest degrease and grind, with a coating built thick enough to shrug off dropped tools and steel implements.

Storage warehouses

Pallet jacks and loaded carts roll the same lanes all day. A hard topcoat and inlaid aisle lines keep those lanes readable and stop wheels from wearing through to bare concrete.

Farm shops

Benches, welders and parts washers. Chemical resistance counts for more than color here, and a broadcast flake with a working texture keeps footing sure when the floor is wet.

Converted barns

Older buildings turned into storage or workspace often sit on slabs poured in stages. Sounding finds the hollow sections and density changes before anyone decides what to grind and what to replace.

Wheels, loads and the hollow spots

Pallet jacks and rolling loads punish a coating in ways foot traffic never will. A loaded wheel puts its full weight on a tiny contact patch, and any weakness under the floor shows there first. A void beneath the surface flexes every time a jack rolls across it, until the coating cracks around the edge.

Sounding finds those voids. Johnny walks the slab with a hammer, listening for the dull note of an empty pocket, and marks where the density shifts from one pour to the next. On older ag buildings those shifts can come every few feet. Some sections need only grinding. Others get cut out and rebuilt before any coating goes near them.

Rolling loads also decide the texture. A heavy broadcast that grips boots well can make a pallet jack harder to push and collect grit in the wheel lanes. We usually keep the aisles a touch smoother and put more texture near doors, wash areas and anywhere the floor gets wet.

Control joints get a flexible filler that runs up through the finish, so the slab can shift with the seasons without splitting the floor above it.

A hollow spot under a busy pallet lane is a crack with a date already set.

Wind, open doors and harvest dust

Many of these buildings run with the roll-up doors open for air. That suits the people working inside and does a wet coating no favors. Fine dust off the fields drifts in during harvest, and whatever lands in the resin before it cures stays as a gritty haze. Nobody can buff it out afterward.

So the building gets closed up for the pour. Doors come down, gaps get taped, and the floor is vacuumed and tacked off right before the first coat goes on. Where the doors truly have to stay open, the pour waits for a calm day and for a week when the neighboring fields are quiet. Johnny would rather move a date than seal dust into your floor.

Field work sets the rest of the calendar. If the building holds equipment or stock that has to move during harvest, the job gets split so one half stays in use while the other cures, with the seam placed under racking or along a door line.

Moisture can come from below as well. Slabs poured before vapor barriers were common can hold water into spring. Humidity probes go in before scheduling, and a high reading puts a moisture-tolerant primer under the system.

Equipment, shop and storage floors are covered in more depth on our warehouse flooring page.

What ag and warehouse owners want to know

Can you coat a slab that has soaked up diesel for years?

Usually, yes, but it takes more prep than a clean floor. We degrease, grind aggressively and then check whether oil is still surfacing. If it is, the floor gets a second round. Coating over contamination that is still in the concrete leads to peeling, so we do not skip that check.

Will pallet jacks wear through the coating?

Not when the system is built for them. Wheel traffic calls for a thicker build and a hard topcoat, plus sound concrete underneath. Most early wear in warehouses starts over a hollow spot or an open joint, which is why we sound the slab and fill joints flexible before the first coat goes on.

Our doors stay open for air. How do you keep dust out?

We close the building for the pour wherever we can, tape the gaps and tack the floor off just before coating. When the doors cannot come down, we pick a calm day and avoid weeks of heavy field work nearby. Dust in wet resin is permanent, so the timing is worth getting right.

Can aisle and safety lines go into the floor?

Yes. Pallet lanes, parking spots for equipment and keep-clear zones are laid into the coating before the clear goes over them. Because the lines sit under the topcoat, forklift and jack wheels wear the clear first, and the markings stay sharp far longer than paint rolled on top.

What happens if the slab has hollow or crumbling sections?

We find them before pricing. Johnny sounds the whole floor and marks voids and spots where the concrete changes density. Small areas get ground and patched. Larger hollow sections are cut out and replaced. All of it appears as its own line in the written price, separate from the coating.

Do you test for moisture on older farm buildings?

Yes. Older slabs around town were often poured straight onto soil with no vapor barrier. Humidity probes go into the slab before we schedule anything. If the readings are high, a moisture-tolerant primer goes down first.

Get the slab read before harvest

Send the size of the building, what rolls or drives across the floor and what has spilled on it over the years. Johnny drives over from Hollister, sounds the slab, probes it for moisture and takes a hard look at the oil stains. The written price lists grinding, repair and coating on separate lines, and the pour date gets picked around the wind and your field work.

Shop and commercial floors we have finished are in the gallery. If writing suits you better, send the building details here and Johnny will follow up.