Boards Kept Safe From Static at Ridgemark Home Benches
Johnny Mendoza works out of Hollister, next door to the Ridgemark course, and very few houses around it will ever need an ESD floor. The rooms where it can pay off are narrow: a bench where someone opens up golf cart or e-bike controller boards, a hobby room built around a soldering iron, a home office where hardware gets taken apart.
JP Resin Certified · Don Resin Certified · Hollister Based, Next Door to Ridgemark
Ridgemark sits just southeast of Hollister, so Johnny is practically a neighbor.
Why most houses on the course pass on it
Static only matters when someone carries a charge to a circuit board while the board is open. A dry room and a pair of rubber soles can load a person up with enough charge to hurt a chip, well below the level you would ever feel as a snap. Nothing smokes. The part acts strange for a while, then quits, and nobody connects it to the walk across the room.
Around Ridgemark, most of what plugs in stays closed. The TV, the router, the cart charger and the desktop computer all live inside their cases and never meet a bare hand. A garage that parks the cart and the car and holds the golf bags has no reason to carry a grounded floor, and Johnny will steer you toward a coating that suits how the bay really gets used.
Ask who opens electronics in the room. If the answer is nobody, keep your money.
The exceptions are real, just rare. Golf carts and e-bikes run on motor controllers, and some owners like to diagnose and repair those boards themselves at a bench in the garage. Drone builders, ham radio operators and people who fix audio gear end up in the same spot. So does a home office where the person at the desk swaps drives and cards in a small rack.
In those rooms the floor is one piece of a system. It only helps when the person is grounded through heel straps or ESD shoes and the bench is tied to ground as well.
Four Ridgemark spots Johnny will look at
The deciding detail is never the square footage. It is whatever sits on the bench with its cover off.
Cart controller bench
A golf cart’s speed controller is a circuit board in a sealed box, and opening it at a garage bench is exactly the kind of work static can hurt. A dissipative floor under that bench, a grounded mat and wrist strap on top, and heel straps make a complete setup.
Battery charging corner
Charging the cart is a separate job. The battery maker’s manual is the guide for ventilation, spacing and where the charger mounts, and Johnny plans the floor around it. Most of the time that corner wants a chemical-resistant coating more than a static floor.
Home office with gear
A desk with a network cabinet and a workstation rarely needs a grounded floor while the cases stay shut. When someone at that desk regularly pulls drives, seats memory or swaps cards, a grounded zone under the chair and the cabinet is worth talking through.
Electronics hobby room
Soldering stations, radio kits, drone frames and guitar pedals spread across a table in a spare room or one end of the garage. If boards come apart there most weekends, a dissipative floor and a grounded bench keep charge away from whatever is open on the table.
How a garage slab becomes part of a ground path
Most of the work happens before the floor looks like anything. Johnny grinds the garage slab to open it up, fixes cracks and soft spots, and primes it. Thin copper tape goes down on the primer and runs to a ground point in the house, one an electrician has checked. A conductive primer covers the tape and ties the whole area together.
The top layer is an epoxy or urethane with conductive fibers or fillers mixed through it. How much goes in decides which kind of floor you end up with. A conductive floor moves charge off very quickly and suits rooms with the touchiest parts. A static dissipative floor lets charge bleed away more slowly, and for a hobby bench or a controller repair table it is the usual pick.
A house has no written static program, so Johnny sets the target range with you before the work starts, based on what the makers of your parts and tools recommend. Once the floor cures he checks it with a resistance meter at several spots, then again with you standing on it in the shoes you plan to wear.
A grounded floor does nothing for a person standing in rubber soles.
Golf cart grit, rolling chairs and the mop bucket
A garage in a golf community collects grit. Carts roll in with sand off the paths and dust from the course, and a fine layer of that sitting on a dissipative floor changes how it reads. A mat where the cart comes in, a broom on the bench side and a weekly dust mop keep the surface clean enough to do its job. Keep cleated golf shoes off the grounded section too, since they drag grit right across it.
Wax undoes the whole thing. A glossy floor finish or the wrong all-purpose spray dries into a thin skin that stops charge from moving, and the next meter check shows it. Johnny writes down a cleaner that leaves nothing behind. Swap the bench chair’s casters for dissipative ones as well, since plastic wheels leave the person in the seat floating.
Because Johnny is local, a small bench zone in a garage fits into a few working days plus cure time, and coming back to recheck readings is easy. If the rest of the bay needs a floor for parking and storage, that part can get a regular coating at the same time, with the grounded zone marked off clearly. The full breakdown of conductive and dissipative systems sits on our ESD flooring page.
What Ridgemark tinkerers ask about grounding
Does charging a golf cart in the garage mean I need a static floor?
No. Charging batteries is not static-sensitive work in the way an open circuit board is. The battery maker’s guidance covers ventilation and where the charger should sit, and Johnny follows it. That corner usually needs a floor that handles an acid drip and wipes clean, which a regular coating does well.
I repair cart and e-bike controllers at home. What setup fits that?
A dissipative zone under the bench is the usual answer, tied to ground, with a grounded mat and wrist strap on the work surface and heel straps for whoever sits there. The zone can be the bench footprint plus room to stand and roll a chair, so the rest of the garage stays an ordinary floor.
Will the grounded floor hold up if a cart battery leaks on it?
The body coat is an epoxy or urethane, so an acid drip wiped up promptly should not hurt it. A battery that leaks often belongs somewhere else, though, and charging is better kept off the grounded zone entirely. Johnny lays out the garage so the charging corner and the repair bench sit apart.
My home office is upstairs over a wood floor. Can the system go there?
Johnny’s ESD systems are built on a slab, so a wood-framed upstairs room is a different job. In that case he will usually point you to a grounded mat setup at the desk and keep the floor work for a garage or a ground-level room. If the office can move downstairs, that opens the door.
There is no spec for a house. How do you pick the reading the floor should hit?
Johnny starts with the parts and tools you work on. Board and tool makers often state a range for the work surface and the floor, and that sets the target. For most home benches a static dissipative floor is the fit. He writes the range down before the pour and checks against it afterward.
Can the golf cart still park on the grounded part of the garage?
It can, and the floor takes the weight without trouble. The catch is dirt. Tires carry grit and turf in, and a film of dirt on the surface changes the reading. Most owners keep the cart on the regular side of the bay and leave the grounded zone for people and benches.
Let Johnny decide if your bench needs it
Call or write with what you work on, where the bench sits and whether the cart charges nearby. Johnny comes over from Hollister, looks at the slab and the setup, and works out with you whether a grounded floor is worth it. If a regular coating covers the need, he will tell you that instead.
See finished floors in the gallery, or describe the room here and Johnny will write back.