Skip to content
Packing Sheds and Cold Rooms

San Juan Bautista Cold Rooms on Urethane Cement

Produce comes off the fields around San Juan Bautista and goes straight into a cooler held just above freezing. At the end of the shift a crew hoses that same floor with hot water and sanitizer. That swing cracks most coatings within a season or two. Johnny Mendoza trowels urethane cement thick enough to ride it out, and he looks hard at the cooler door before anything else.

JP Resin Certified · Don Resin Certified · Hollister Based, Close to San Juan Bautista

From Hollister, Johnny takes Highway 156 west to the mission town and the farms around it.

The temperature swing a packing floor lives through

Thermal shock is what kills these floors. A cooler slab sits cold for hours. Then hot rinse water hits it, and the top skin warms and grows while everything a quarter inch down stays chilled. A thin, rigid coating cannot stretch with that. It shears at the bond line, a little more each day, until whole sheets lift near the door and around the drains.

Urethane cement is built for exactly that abuse. It moves much more like the slab underneath it, and it goes down thick, troweled or poured as a slurry, so a dropped crate or a pallet jack wheel has plenty of material to dent before it reaches anything that matters. It also puts up with a damp slab far better than epoxy, which counts in a room that sweats every time the door opens.

A cold room floor gets graded in the minutes after the hot hose comes out.

Pallet traffic piles on top of all that. Forklifts and jacks run loads from the cooler to the dock all day, and the strip at the cooler door takes every one of those trips along with the change in temperature.

The finish is matte and plain, in a short list of colors. It is a floor for work. Nobody tours a packing shed for the floor, and the crew cares far more about footing than looks.

Operations Where heat, cold and water meet

Four working rooms on the farms near town

In each one the cleaning routine, more than the product being handled, sets the spec.

Produce cooler

Pallets roll in warm from the field and sit on a cold floor that condensation and melting ice keep damp most of the day. A lightly textured slurry gives forklift tires grip, and the cove runs up the insulated panel walls so water cannot sit at the seam.

Packing line

Wash tanks splash, trimmings pile up under the belts and the whole area gets hosed every night. The floor is pitched toward drains that the coating is feathered into, and the texture is set heavy enough for wet boots yet light enough to squeegee clean.

Cidery or winery room

Pressing fruit leaves acid and sugar on the floor, and tanks get cleaned with caustic and hot water afterward. Urethane cement shrugs off both. The coved base wraps around each tank pad, so pomace and juice have no crack to work their way into.

Commissary or bakery back room

Sheet pans come out of the ovens hot, flour turns to paste the moment it meets mop water, and fat finds every low spot. A finer texture here mops easily, and the floor goes back into use fast enough to fit between bake days.

The strip where the cooler meets the dock

Ask anyone who has run a cold room for a few years where its floor failed first, and they will point at the door. That strip takes the most wheels, the most water and the sharpest temperature change in the building, all in a band a few feet wide. Cold air rolls out every time the door opens, and the floor on the warm side sweats.

Johnny starts by finding out how the cooler was built. Some sit on their own insulated floor, and some are panel walls set straight onto the building slab. That decides whether the urethane cement runs inside or stops at a sealed edge at the threshold, and where an expansion joint has to stay open so the two parts can move without tearing the new floor.

Curing is the other catch. The material needs warmth to set properly, so a cooler cannot keep running while the floor goes down. The room gets emptied, shut off and brought up to temperature first, which is why most of these floors go in during the slow weeks between crops. Johnny sets humidity probes in the slab as well, since years of condensation can leave it damp.

Most cold room floors give out at the door, where every load and every temperature change crosses.

Footing on a floor covered in wet produce

Leaves, peels and water on a smooth floor make a slick mess, and a packing crew spends the whole shift standing on it. Texture is the answer, and the trick is choosing how much. A heavier broadcast holds boots in place by the wash tanks, while a finer one in the cooler lets the crew push debris to the drain in a single pass. Johnny lays samples so the shift lead can stand on them.

Drainage gets checked before the first coat. Urethane cement follows the slab under it, so a low spot that holds a puddle today will hold one on the new floor too. Those spots get built up during prep, and trench drains and floor sinks are cleaned out so the coating can be feathered right into them and sealed at the edge. A drain that sits proud of the slab gets lowered, because the lip around it traps dirty water.

The chemistry of the cleaning matters as much as its temperature. Chlorine sanitizers, quaternary products and the occasional acid descaler all land on these floors, and Johnny checks each one against the system before he commits to it. Photos of the jugs your crew uses save a lot of guesswork. More about the system itself is on our urethane cement page.

Cold room and packing shed questions

Can the floor go down while the cooler keeps running?

No. Urethane cement needs the room warm to cure properly, so the cooler gets emptied, switched off and allowed to come up to temperature first. Most growers schedule this in the slow stretch between crops. Johnny gives you the shutdown length at the site assessment, so you can line up other cold storage ahead of time.

Will our nightly chlorine sanitizer wear the floor down?

It should not. Urethane cement resists the common sanitizers used in produce handling, chlorine at normal strengths included. Trouble usually comes from a product mixed far stronger than the label calls for, or left to pool for hours. Give Johnny the product name and how your crew mixes it, and he will confirm the fit.

How do you keep the packing line from turning slick?

With texture chosen zone by zone. Around the wash tanks and under the belts, a heavier aggregate goes into the floor where water and trimmings land. Walkways and the cooler can go finer so they squeegee clean. Samples at the site assessment let the people who actually work the line choose what feels right underfoot.

Our shed floor has puddles that never drain. Can that be fixed?

Usually. Urethane cement follows the shape of the slab, so low spots get built up during prep before the main coat goes down. Johnny checks the fall toward each drain with water during the site assessment and points out any area where the slab itself would need more than a fill to drain properly.

Can a small cidery use the same floor as a packing room?

Yes, the same family of material works for both. A cidery sees more fruit acid and caustic cleaning and less pallet traffic, so the texture and thickness shift a little. The cove around the tank pads and the detail at each drain are the parts that matter most in a pressing room.

What happens to the expansion joints in the shed?

They stay joints. A joint that moves with the seasons has to keep moving, so Johnny carries it up through the new floor and fills it with a flexible sealant. Cracks that have stopped moving get cut, filled and coated over. Bridging a live joint with rigid material only moves the crack somewhere else.

Show Johnny the cooler door

Send the size of each room, what runs through it and when your slow weeks fall between crops. Johnny drives over from Hollister, checks the slab for moisture, looks at the drains and the cooler threshold, and writes up a price with the prep work on its own lines so nothing surprises you later.

Past work is in the gallery. Rather write it out? Send the room sizes here.