Skip to content
Kitchens And Food Plants

Urethane Cement That Takes the Steam in Fremont Food Plants

Steam hoses at the end of a shift and a freezer door that swings open all day. A standard epoxy can crack under that kind of heat swing. Urethane cement goes down thick, moves with temperature and puts up with a damper slab. Johnny Mendoza installs it where food gets made around Fremont, from production rooms near Warm Springs to busy restaurant kitchens.

JP Resin Certified · Don Resin Certified · Based in Hollister, Working Fremont

Johnny drives up from Hollister through San Jose to Fremont’s kitchens and production floors.

Heat swings are what break a food floor

A food production floor goes through a temperature fight every day. Boiling water and steam hit it at cleanup, cold air pours out of the freezer and cooler doors, and hot oil lands near the fryers. A thin, rigid coating expands and contracts at a different rate from the slab beneath it, and after enough cycles it cracks, then peels at the edges.

Urethane cement handles that because it behaves closer to the slab itself. It is troweled or poured as a slurry at a real build, often a quarter inch or more where carts run, and it tolerates thermal shock that would craze a thin film. It also stands up to food acids, sugars, blood, brine and the sanitizers a plant runs through every night.

Your cleanup crew’s hose is a harder test than anything a forklift does.

It is working floor, though, rather than a showpiece. The finish runs matte to textured, the color range is short, and you get a floor that looks like it belongs in a plant because it does.

Then there is the slab under it. Plenty of the older industrial space in Fremont sits on slabs poured without a vapor barrier, and the low ground toward the bay can read damp. Urethane cement tolerates more moisture coming up through the slab than an epoxy system will, which often makes it the safer call even before the heat question.

Zones Where the heat and water land

Food rooms built for a hose-down

Each room takes its own beating, so the thickness, texture and cove detail change from one to the next.

Food production rooms

Mixing, cooking and packing lines with daily washdowns and sanitizer. The floor goes down at full thickness near kettles and ovens, feathers into the floor drains, and climbs the walls in a coved base so the corners never hold food or water.

Commercial kitchens

Hot oil at the fryers, boiling water at the dish pit and grease that gets scrubbed out every night. Urethane cement takes the heat that softens thinner finishes, and a textured broadcast keeps a cook steady in wet shoes through a long service.

Wash bays

Truck, equipment and tote washing puts pressure water, detergent and grit on the floor all day. A heavier texture holds footing, the cove keeps spray off the base of the wall, and the floor goes back to work quickly after install.

Cold storage doors

The threshold where a freezer meets a warm dock takes the worst temperature swing in the building, plus pallet jack wheels. That strip gets full-thickness urethane cement and careful detailing at the door track so frost melt cannot work its way underneath.

Where a food floor actually fails

Walking lanes rarely give out first. Trouble starts at the edges: the joint where floor meets wall, the lip around a floor drain, the strip under a kettle that drips all shift. Water finds those spots, and once it gets underneath, bacteria and lifting follow. Grout lines in old quarry tile fail the same way, just slower.

So the edges get the most attention. Urethane cement is coved up the wall in one continuous piece, so there is no seam to scrub around. At drains and at the open edges it is cut in and keyed into the slab, a detail installers call an anchor groove, which keeps the floor from creeping or curling where water runs hardest.

Cleanup chemistry gets asked about early. Johnny wants to know which sanitizer you run, how hot the water is and whether you steam clean, because those answers set the texture and the topcoat. A floor that cleans well with a squeegee and a hose is worth more to a sanitation crew than any color choice. Inspectors notice a floor that holds standing water, and so does the crew that has to push it out every night.

Ask your sanitation lead what hurts. That person knows the floor better than anyone.

Older slabs, damp ground and getting the line back on

Fremont has a lot of food production in older industrial buildings, and those slabs come with history. Oil soaked in around old equipment, sealers nobody remembers, cracks from settling. Before anything is mixed, Johnny grinds and degreases, cuts out what will not clean up and sets humidity probes in the slab, because a floor that blisters in a food room means pulling it up and losing days of production.

Urethane cement forgives more slab moisture than epoxy, but it still needs a sound, clean surface to grab. The probe readings decide the primer and the prep, and you see that on the written price before work starts, so nothing changes once the crew is in. Control joints get honored, with the new floor cut back at the joint so the slab can move without cracking the surface above it.

Return to service is one of the reasons plants choose it. Many urethane cement systems take foot traffic and light carts quickly and handle full loads soon after, so a section can often go down over a weekend shutdown while the rest of the plant keeps running. For a deeper look at the systems and where they fit, see our urethane cement page.

What Fremont food producers ask before a new floor

Can urethane cement go inside our freezer?

The floor inside an operating freezer is a hard install because the material needs warmer temperatures to cure. Most of the time the room is shut down and brought up to temperature first. The freezer threshold and the dock outside are easier, and those are often where the worst damage is anyway.

Will it be slippery when it is wet and greasy?

Texture is part of the build. Aggregate is broadcast into the material or a textured slurry is used, heavier in front of fryers, kettles and wash stations. The aim is footing for someone in wet boots on a floor that still squeegees clean at the end of the shift.

Can we get a color that matches our brand?

Within limits. Urethane cement comes in a short list of colors, mostly practical tones like tan, gray, red and green, and the finish stays matte to textured. If a front-of-house space needs a showpiece look, Johnny will usually suggest a different system there and keep urethane cement where the heat is.

Our restaurant near Mission San Jose closes one day a week. Is that enough?

It depends on the size of the kitchen and what has to come up first. Old tile and mastic take time to remove. Smaller kitchens can sometimes be done across a closed day and a night, with the work planned so cooks are back on the line when you reopen. Johnny lays out the real timeline at the site assessment.

Does a wash bay need the same floor as a kitchen?

The material is similar, the details are not. A wash bay sees pressure water, grit and detergent rather than hot oil, so it usually gets a coarser texture and a taller cove where spray hits the wall. The weight of the vehicles or equipment rolling through also shapes the thickness Johnny specs.

We have quarry tile now. Can you go right over it?

Usually no. Quarry tile with failing grout traps water and grease under the new floor, and the bond depends on the tile staying put. Johnny normally removes the tile and grinds down to the slab, then repairs any low spots so the new floor drains the way it should.

Bring Johnny into the kitchen or the plant

Tell Johnny how big the room is, what you cook or pack, how you clean and when you can shut down. He drives up from Hollister, walks the floor with whoever runs sanitation, probes the slab and hands you a written price that splits the tear-out from the new floor.

Finished floors are in the gallery. Not near a phone during service? Write it out here and Johnny will call back after the rush.